It’s All About Wig Making
The subsequent Step – Sorting out the hair..
The subsequent step within the wig making course of, for me, is ventilating the hair onto the principle body of the wig. In order to do this one wants some ‘spare’ hair. Beyond deciding such things as – the hair origin (European, Chinese, Indian, Mongolian and so on), hair kind (virgin, cuticle, processed), hair texture (wavy, straight, curly, body wave and so forth) and length, you could have a few choices. You can both use hair you have already got (previous wefts, old wigs and so on) or purchase some new hair (both as wefts or bulk/uncooked hair in ponytails). As talked about in my last blog put up, I already had some lots of hair on essentially the most ridiculous wig recognized to man. Because of my novice standing, I decided that this was the msot applicable hair to make use of. I think that in the sooner stages of wig making it is probably a greater concept to use inexpensive hair. Then should you go utterly flawed, you won’t be as devastated as you’d in case you have been utilizing virgin cuticle European hair, for example.
Aspect note – I do have higher hair – uncooked and wefted, which I hope to use later when I’m extra proficient. Definitely if I were choosing hair, I could be inclined to go for raw ponytails of caucasian/European origin – as a result of that texture is identical as my bio hair.
Because the hair is already attached to a wig, I set about the process of brushing the wig out, separating the hair and eradicating some. I decided the hair team that first separating the hair in half (to effectively create two ‘tails’) was a good idea as there is about twice the amount of hair I need in my new wig. On the left hand aspect you can the hair team see half the hair has been braided; to maintain it neat and out of the way. The right hand side represents half the hair and is what I’m going to use on this wig.
You may see simply how much hair is in half the wig on this subsequent image, the place I am holding that braid in my hand.
At this level I have the half, for use, hanging unfastened ready to be sorted.
As the hair is already ventilated onto this wig, I don’t need to only lower it off as a ponytail/braid. If I did this, I would lose lots of the upper length. In order to keep this length, I need to remove the hair in the stages I’m going to use it. As most people begin ventilating at the underside of their wig foundation, I must take the underside lengths to use on the underside of my wig foundation. So, I braided the rest of the hair and solely left free the half I need to remove from the bottom proper hand nape.
I then clipped this braid up. The hair hanging down is only half of the hair at the bottom of the nape of the wig.
I’ve drawing cards prepared to put the hair into (they’re the flat brown and grey squares to the best of the wig two footage above). This helps to keep the hair neat whilst I’m ventilating and enables me to take away small amounts of hair to work with. In the event you shouldn’t have drawing playing cards and get a pair, remember to put in writing “Root” on one finish of them (I wrote it on each sides) so that you understand which method up your hair is! You place the unfastened hair into the drawing cards with the basis finish of the hair at the top you may have designated “Root” and the tip ought to be hanging out the opposite finish. This enables you to keep it cuticle correct.
I carefully cut sections of the unfastened hair away. I tried to maintain fairly close to to the wig cap so that I might keep most of the size. I just used common scissors for this.
Then I positioned the hair in the drawing cards.
After I shut them up, I always put an elastic band round them. That approach, if I (or anyone else!) ever knock them onto the ground, they will not fall apart and wreck the hair (as a result of if the hair gets blended up, it will not be cuticle appropriate anymore).
If you cherished this short article and you would like to acquire much more info regarding extensions kindly check out our site.